Analýza vybraných vlastností různých typů polymerů zpracovaných technologií FFF – Bc. Daniel PRŮŠA
Bc. Daniel PRŮŠA
Master's thesis
Analýza vybraných vlastností různých typů polymerů zpracovaných technologií FFF
Properties of Different Types of Polymers produced by FFF technology
Abstract:
Tato diplomová práce je zaměřena na vzájemné porovnání vybraných vlastností deseti polymerních materiálů zpracovaných technologií FFF. Jedná se o nasákavost ve vodě, teplotu průhybu při zatížení, rázovou houževnatost, tvrdost a ohybové a tahové vlastnosti. Teoretická část práce obsahuje základní seznámení s 3D tiskem. Zabývá se jeho metodami a materiály, které se v této oblasti využívají, zejména termoplastickými …moreAbstract:
This thesis is focused on the mutual comparison of selected properties of ten polymeric materials processed by FFF technology. These are water absorption, deflection temperature under load, impact toughness, hardness and flexural and tensile properties. The theoretical part of the thesis includes a basic introduction to 3D printing. It discusses its methods and materials used in this field, especially …more
Language used: Czech
Date on which the thesis was submitted / produced: 13. 5. 2024
Accessible from:: 31. 12. 2999
Thesis defence
- Supervisor: doc. Ing. Jaromír Cais, Ph.D.
Citation record
ISO 690-compliant citation record:
PRŮŠA, Daniel. \textit{Analýza vybraných vlastností různých typů polymerů zpracovaných technologií FFF}. Online. Master's thesis. Ústí nad Labem: University of Jan Evangelista Purkyně in Ústí nad Labem, Faculty of Mechanical Engineering. 2024. Available from: https://theses.cz/id/o8yq6l/.
The right form of listing the thesis as a source quoted
PRŮŠA, Daniel. Analýza vybraných vlastností různých typů polymerů zpracovaných technologií FFF. Ústí nad Labem, 2024. diplomová práce (Ing.). UNIVERZITA JANA EVANGELISTY PURKYNĚ V ÚSTÍ NAD LABEM. Fakulta strojního inženýrství
Full text of thesis
Accessibility: Autor si nepřeje zpřístupnění práce veřejnosti
Contents of on-line thesis archive
Published in Theses:- Soubory jsou nedostupné.
Other ways of accessing the text
Institution archiving the thesis and making it accessible: UNIVERZITA JANA EVANGELISTY PURKYNĚ V ÚSTÍ NAD LABEM, Fakulta strojního inženýrstvíJAN EVANGELISTA PURKYNĚ UNIVERSITY IN ÚSTÍ NAD LABEM
Faculty of Mechanical EngineeringMaster programme / field:
Materials and Technologies in Transport / Materiály a technologie v dopravě
Theses on a related topic
-
Výroba tvarových vložek vstřikovací formy pomocí technologie aditivní výroby
Jan Voborník -
Návrh a výroba konstrukce modulu pro ruční tisk s využitím aditivní technologie
Vojtěch Pixa -
Výroba posuvného kolečka z 3-stupňové převodovky historického motocyklu pomocí technologie SLM
Vilém Jílek -
Návrh aditivní technologie výroby rotoru automobilového ventilátoru
Jakub Hrabalík -
Možnosti tvorby komponent pro aditivní technologie výroby za využití algoritmického modelování
Ondřej ŠPAČEK -
Možnosti využití aditivní technologie pro výrobu orientačních bodů rozšířené reality
Vojtěch Veselý -
Měření opakovatelnosti výroby z aditivní technologie
Michal Bednář -
Využití kovové aditivní technologie při výrobě oběžného axiálního kola turbínového motoru pomocné energetické jednotky
Jan Robl